NORDSON CK5400 POWDER PAINT BOOTH WITH 3 CYCLO-KINETIC

Page 1 of 4

Manual Powder Gun Equipment
(2)Versa-Spray II, light weight, featuring easy clean, low maintenance
design
(2)Gun extension (s), 150 mm Lg
(2)Gun control unit(s), function includes adjustable KV and powder outp
ut controls
(1)Blow off gun assembly(s)
(1)Sturdy operator platform(s), 3'-0" x 3'-0" with safety rails
Automatic Powder Gun Equipment
(1)Versa-Spray II Control Console(s), w/MC-3, 19" Rack Design with Mast
er Control
Units. Includes ten (10) IPS control units, fully adjustable in KV and
powder
output, featuring LED bar readout for monitoring of either KV setpoint
or
microamp current output.
(10)Versa-Spray II Guns w/air wash and ion collector kit and mounting b
racket(s),
designed with snap-away construction for easy servicing.
Automatic Gun Mounting Equipment
(2)Gun support stand(s)
Booth Canopy
6'-0" width x 24'-10" overall length, including2'-0" air flow directing
external vestibules, featuring
*Polypropylene wall & roof panels
Low conductivity design for higher transfer
Efficiency and easy cleaning
*Gun and conveyor openings with polypropylene vestibules
(2)Manual gun openings, with easy access to inside of booth, 2'6"W x 3'H
(4)Automatic gun openings with vestibules 6"W x 6'H
(2)12" Curved efficiency extension(s) designed for increased air flow
(2)Profile end opening(s) 2'6"W x 5'H
Powder Supply Equipment
(2)Hopper(s), Model HR-16-150, 150# capacity with direct vent and level
control, automatically maintains consistent level of powder in feed hop
per,
control timers and solenoids are located in the electrical control pane
l.
(2)Electric-powered automatic powder sieve assembly(s), rotary sieve ty
pe,
230/460 VAC, 3 Phase, 60 Hz. Complete w/installation hardware, includin
g
platform support.
(4)Sieve screens,additional
(24) 100 Plus pumps and mounts featuring quick-disconnect type pumps fo
r
easy cleaning and servicing
(2)Set powder delivery hose and tubing for each gun
(1)Vibratory box unloader, dolly mount with one transfer pump
(1)Lot,spare parts
Recovery/recycle Equipment
Nordson Base Assembly, complete with
(1)Stainless steel floor includes all pipe and electrical conduit
as detailed under pre-shipment assembly
Nordson Fan Assembly, Model CK03SI, complete with
(1)Dual exhaust fan assembly, total air flow of 5400 CFM, 40 HP motor,
230/460 VAC, 3 phase, 60 Hz.
Nordson Cyclo-Kinetic Separator, Model CK03SI complete with
(1)Powder coated cartridge after filter, 5400CFM designed to NFPA stds.
(3)Cyclo-kinetic separators
(3)Transfer pump(s) to return oversprayed powder to the feed hopper, ar
e
automatically operated by a level control in the feed hopper
Booth Control Equipment
Connected and wired to the booth base assembly for easy field terminati
on.
(1)Electrical control panel and safety interlocks 230/460 VAC, 3 Phase,
60 Hz
(1)Pneumatic control panel, 90 PSI, clean and dry air
Fire Detection System Control Panel
(1)Fire detection panel, programmable, micro-processor based, self-
monitoring, with diagnostic readouts and audible alarm, factory mutual
approved for maximum operating system
Page 3 of 4
(2)Fire sensor heads with test light source, 120 degree field of view.
Senses UV, IR and Visible light, response time less than 1/2 second.
Control Equipment
(1) Versa Screen 5c Color Touch Screen for system setup, system monitor
,
and system alarm. The 320 x 240 resolution screen provides (8) colors
for graphics. The backlit touch screen provides easy access to setup an
d
run information.
The Versa screen terminal will provide interface to all the finishing s
ystem
information. Functions will be provided to run the guns in both manual
and
automatic mode.
All alarm information will be provided on an alarm screen.
Booth Control Center
(1)Allen Bradley SLC5/01 system(s), with EEPROM,to control gun operatio
ns. The
EEPROM provides the capacity to retain the program after battery loss o
r
processor replacement.
The PLC will provide the ability of the guns to cycle on/off based on p
art height
and length. Various trigger patterns can be used by adjusting a simple
parameter
set. This system has the following capabilities
a.) Up to 12 individual gun trigger point.
b.) Up to 6 photoeye input points.
c.) 1 encoder input
d.) 1 booth interlock input
(1)Encoder with reducing sprockets. Customer must install encoder brack
et to conveyor
drive so the encoder is within 300 ft of cable-length from PLC.
(5)Photoeye to determine part height and/or length
This system contains 5 zones per booth
(1) Part Identification Stand for photoeyes and/or light beams.
Provides a remote location to mount part identification sensors for bot
h
vertical and horizontal sensing
Page 4 of 4
Optional Equipment
Regenerative air drying equipment,
(1)Twin Tower Regenerative Air Dryer, 150 CFM @ 100 PSIG, 115 VAC, 1
Phase, 60 Hz.
Includes particulate filter at 40 microns and oil coalescer at .03 Micr
ons