D & H 60" WIDE X 8" ARBOR X 40,000 LBS. SLITTING LINE

Page 1 of 4
GENERAL SPECIFICATIONS:

Entry Coil Car-Side mast type
Self contained, 5 hp Hyd. power unit
Lift by Hyd. Cylinder 18" (460mm)
Travel by Hyd. Motor 15' (4.57m)
Uncoiler, Mandrel type
Powered hold down roll, Urethane covered
Hyd. Expansion 19.5"-24.5" (508-609m)
Sliding base, 6" Cylinder travel
Hyd. motor feedup & braking
5 6 1 Internal reducer
Coil Threading Table
Hydraulic Cylinder Lift & Extend
Power Adj. Edge Guides-roller type
Automatic Mechanical Edge Control-mounted with the edge guides
Driven Punch Rolls- hydraulic motor drive, hydraulic cylinder
gap adjustment
Hydraulic Crop Shear with Rack & Pinion Rake Angle
Mounting
All Units on One Common Base
Slitter, Removeable Head Type (Crane)-No. of Heads (2)
8" Dia. Arbors
Jet Nuts for Tooling Lock-up
Timken Bearings used Throughout the Head
Square Gear Internal Design with One Output for Driving the Head
Hyd. Adj. Outboard for Changing Tooling
Over the Arbor Bearing Design
Outboard Support Adj. in to 36" to Reduce Arbor Deflection for Heavier Sl
itting
Duff Norton Jacks-Hyd. Motor Powered With Digital Readout For Knife Posit
ion
150 HP DC Motor- 650-2000 RPM
Falk Reducer with Coupling and Overrunning Clutch
I. K. S. Shimless Tooling
Scrap Winder-Number of Units (2)
40" Dia. x 12" Wide Ball 1016mm X 305mm
Approx. Ball Weight 2,500 Lbs.
Hyd. Drive Motor Charlynn
Capacity per Side 2" Wide x .250"
Pit Rolls and Pit Covers
Scratch Proof Covers on Table
Tension Stand
Combination Pad & Rubber Covered Roll Type
Air Bag Type Drag Stand, Hyd. Cylinder Opening
Entry & Exit Separator Bars
16" dia. Urethane Rolls- Offset Design, Hyd. Motor
Feedup Drive
(2) Water Cooled Brakes- 16" Dia. Wichita
Hydraulic Clyinder Top Roll Adjustment
Duff Norton Jack Bottom Roll Adjustment
Recoler with Overam Separator
20" Dia. Drum
61 Internal Reducer
3 Speed Drive-All Reducer
Hyd. Pushoff with Bronze Stripper Plate
Hyd. Grip and Expand
150 HP DC Motor-650 & 2000 RPM
Exit 4 Arm Turnstile with Pushoff
Hydraulic Rotation
Hardened Wear Bars- Bolt On
"U" Shape Design to Allow "C" Hook Lift Off
Hydraulic Equipment
(2) 30 HP Hyd. Power Units
One Entry and One Exit
Page 3 of 4
Electrical Equipment
SCR Drives- Reliance
AC Controls
Panels & Push Button Stations By CMC
Allen Bradley PLC
Consoles
Main Operator Station Plus Misc. Control Panels
Jib Crane for Changing of the Slitter Heads
5 Ton Single Rail
Summary of Specifications
Material
Material Type Steel-Alum-Stainless
Maximum Shear Strength 60,000 P.S.I.
Maximum Gauge .250" (6.35mm)
Minimum Gauge .015" (0.38mm)
Coil Width 18"-60" (457-1524mm)
Maximum Coil Weight 40,000 Lbs
Maximum Coil O.D. 72" (1828mm)
Coil I.D. Entry 20"-24"(508-609mm)
Coil I.D. Exit 20" (508mm)
Machine
Uncoiler Capacity 40,000 Lbs. (20 Ton)
Line Speed - F.P.M. 0-750 RPM (76-152-230
MPM)
Slitter-HP 150 HP D.C.
Slitter Arbor Dia x Length 8" (203mm) Dia. x
62" Long
Page 4 of 4
Recoiler Capacity 40,000 Lbs (20 Ton)
Recoiler - HP 150 HP D.C.
Recoiler Drum Dia. x Face 20"(508mm) x
68" (1727mm)
Line Direction Left to Right
Uncoiler is Presently
Mounted R-L But Can
Be Changed To Correct
Position
Slitting Modes
Pull Thru
Pull Thru with Slitter Drive Assist
Loop Slitting
Owners Manuals, Operation Books & Electrical Diagrams
Are All Available With Complete Drawings