MURATA MARATEC MD-200 CNC TWIN SPINDLE 3-AXIS CHUCKER WITH GANTRY LOADING

Spl. High HP Spindle Drives (22kw/30mn.)
High Speed Gantry Loader with 100mm Z Axis Shift
(2) Live Tool Drives, 3000 RPM, 4 kw
(2) C-Axis Control and Brake
(2) Coolant Pumps (4kg/cm) (60 PSI)
(2) Air and Coolant Mixing Blow Through Spindle
Signal Tower (Red/Yellow/Green), Remote Operation Panel
QC Check Counter and QC NG Chutes, 80m Part Program Storage & Edit
Tool Geometry and wear offsets, Total 16 Pairs of Tool Offsets
Tool Nose Radius Compensation
Inch/Metric Conversion
(2) Hydraulic Chuck Cylinders
Tool Monitor (servo Torque Monitoring)
4 Point Spindle Orientation, Chuck Foot Switches
Ducting Preparation for Mist Collection
Standard Machine Guarding Package
Fanuc Extended 2-Year Warranty
75 KVA Transformer for customers 460V & 480V Power
Chip Conveyor, Rear Discharge
Cont.
SMALL FEEDER TABLE ASSEMBLY WITH LIGHT CURTAINS
Standard Murata work feeder table with interface cables, Model WF14L-160
14 Pallets with stacking height of 450mm, max. part OD approx. 160mm,
and max. stacked part weight per pallet of 35 Kg. Includes light curtain
and guarding assembly. Light curtains included for one side of the feeder table.
SET OF 14 SPECIAL FEEDER TABLE PALLETS
ORIENTATION STATION
3,500 RPM PULLEY CHANGE
WORK LOCATION CONFIRMATION SENDING-ONE SIDE
Work location confirmation sensing includes all wiring, solenoids, and special switches
installed to the machine to verify that the workpiece has properly seated on the chuck
locating surface. This options monitors the air pressure created when the
workpiece is seated in the chuck. If the part is incorrectly seated, an alarm
signal is sent to the machine and the gantry will try to reseat the part or
remove the part to the NG chute.
WORK CLAMP CONFIRMATION-ONE SIDE
Work clamp confirmation includes switches and bracket to verify that the drawbar
stroke for clamp to unclamp has occurred.
TOOLSETTERS
Automatic tool setter to allow for automatic setting of tool geometry after
changing instead of manual tool touch off. Includes hardware and software for
both spindles.
GANTRY ISOLATION STANDS
2M GRAVITY OUTFEED CONV. WITH CONV. FULL SIGNAL TO MACHINE
BAG TYPE COOLANT FILTRATION
SINGLE POINT DEBURR UNIT
This single air driven tool will deburr the backside of the drilled holes
in the flange face. Parts will be held in the machine gantry during the
deburr process. Unit will be mounted within the machine gantry access area.
SPINDLE RIGID TAPPING
COLD START CYCLE
Includes Cold Start Push Button and Special Loader Cycle Programming
CNC OPTIONS
CUSTOM MACRO B
82 Useable Variables
AUTO TOOL SHIFT
(Redundant Tooling)
DIRECT INPUT OF OFFSET VALUE MEASURED B
Required for tool setter
OP10 WORKHOLDING
ITW 8" UBL Universal Ball-Lok Chuck
OP20 WORKHOLDING
PU 208 8" Chuck Body
EDMUNDS GAGE WITH INTEGRATED PARK MAKER
The gage will check the 29.995-0.007/-0.020 Outside diameter in 2 places
the 48.2+0.3/-0 Outside diameter in 1 place, and feed back to the machine
Feedback will include offset for taper. The Murata gantry will load the part
in the gage. After gaging, the integrated part marker will mark each good part
on the periphery of the flange with Julian Date Code and Serial Number.
NG parts will not be marked. The Murata gantry will place the good parts on the
output conveyor. NG parts will be placed in the Murata NG Chute.
Machine Hours 3,794