ELECTROVERT MODEL H-501 P.C. BOARD WASHING SYSTEM

GENERAL SPECIFICATIONS:

The Electrovert Series H-501 Hydro-Cleaner is an advanced p
rinted circuit board
cleaning system. Its modular construction allows you to tailor the
system to your own
specific requirements - from general cleaning to the highest indust
ry standards.
The basic functions of the H-501 System are transporting, c
leaning, rinsing,
wiping, and drying. Transportation of the PCB is supplied by a sta
inless steel wire chain
running through the entire system.
Should your requirements change in the future, the present
modules may be
resequenced and additional modules economically incorporated into t
he system. Multiple
modules may be used to increase production, increase cleanliness, a
nd shorten drying time
of the PCB.
The series H-501 cleaner is constructed of high quality mat
erials. The lower
frames are made of epoxy painted steel. All wetted surfaces, plumb
ing, pumps, and
discharge nozzles are stainless steel.
Conveyor width 20" (18" usable) with 2" depth adjustment
Conveyor speed (approximate) 0 to 196 IPM
Pass line height 32"
Overall size (approximate) 300" L x 66" D x 60" High
Line consists of
1) HL Module (Horizontal Loader)
2) PW Module (Prewasher)
The H-500 SMT series module is designed to provide ma
ss cleaning of printed
circuit boards (PCBs), using either biodegradable det
ergents or neutralizers.
Two (2) upper and two (2) lower spray bars for prewas
h with a 1-1/2 H.P.
Pump.
3) SMT Module (Washer)
Two (2) Coherent Jet (JIC) spray manifolds washing wi
th 10 spray
bars - over the conveyor and 10 spray bars - under th
e conveyor with
dual 7-1/2 H.P. pumps. Upper and lower manifold pres
sure regulating
valves.
4) PRR Module (PreRinse/Rinse)
Six (6) upper and six (6) lower spray bars for recirc
ulating rinse
with one (1) 3 H.P. pump.
GENERAL SPECIFICATIONS:

5) AK Module (Air Knife)
6) DIRD Module (Dual Infra-Red Dryer)
7) DUL Module (Drive UnLoad)
Weir drain protection
Dual spray filters (400 microns)
Low liquid level alarm
Watertight Buna seals
Front mounted manifold pressure gauge set (for performance
monitoring)
Six (6) 9-KW immersion heaters with temperature controller
Technical Data
Power requirements 440 VAC, 3 phase, 60 Hz or 380 VA
C, 3 phase, 50 Hz or
240 VAC, 3 phase, 50 Hz
Pumps 11.2 KW
Heaters 54 KW
Total 65.2 KW (approx)
Temperature Control
Sensor Thermocouple type-J
Heater control Closed loop control with adjustab
le PID variables
Heaters 6 each at 9.0 KW, 3 phase
Temperature range Ambient to 180 degree F (
82 degree C)
Tank Sump Capacity 110 U.S. Gallon (416 L)

Page 3 of 3
GENERAL SPECIFICATIONS:

Spray Manifold
Pumps Two (2) 7.5 HP centrifugal pumps
Impellor 5.75 in. (146 mm) stainless steel
Seals TEFLON
Manifold pressure (Nominal)
H-501 SMT 50 psi (3.51 kg/sq. cm)
H-551 SMT 50 psi (3.51 kg/sq. cm)
Flow Rate (Nominal)
H-501 SMT 150 gpm (567 L/min.)
H-551 SMT 150 gpm
Spray Nozzles
Type JIC
Quantity/Bar 10